iPad yoke mount and EFB tablet mounts for pilots: RAM Mounts
Choose a RAM Mounts EFB mount for your cockpit: yoke clamp, suction cup or rail clamp, the X-Grip holder for your iPad, iPad mini or phone, and a position that keeps controls and view clear.
In this guide
An iPad yoke mount keeps your electronic flight bag (EFB) secure, in view and in reach. This guide helps private and club pilots, flight schools and helicopter operators choose an aviation tablet mount from RAM Mounts for an iPad, iPad mini, Android tablet or phone, and place it so the controls and view stay clear.
![]()
Before you start
- The device model and its case, sleeve or skin
- The outside diameter of the yoke tube or rail
- The aircraft's documentation and any club, school or operator rules for portable devices
- A plan for the charging cable
RAM does not state any aircraft approval or certification for these mounts; don't treat them as certified aircraft parts. The pilot-in-command, and the operator where applicable, decides whether and where a mount and device may be used, following the aircraft's documentation and the authority's rules. The EASA texts quoted here are background, not legal advice.
Which option to choose
RAM points pilots to its “yoke clamp and suction cup bases for secure mounting”. Four ways to carry a tablet:
| Option | Fits on | Good for | Watch for |
|---|---|---|---|
| Yoke clamp | Yoke tube, ≈ 16–32 mm | Moves with the yoke, always in reach | Must not limit yoke travel |
| Twist-Lock suction cup | Windscreen or side window | “glass and non-porous plastic surfaces” (RAM) | Keep it out of your forward view |
| Tough-Claw clamp | Tubes, bars and edges | Tubes and odd shapes, no tools | Solid parts only; check control travel |
| Kneeboard | Your thigh | Writing on the screen; nothing fixed | Not in our online catalogue |
Pick the base: iPad yoke mount, suction cup or rail clamp
Yoke clamp base
The RAM Yoke Clamp Base with Ball (RAM-B-121BU) fits rails from 0.625" to 1.25" in diameter (≈ 16–32 mm) and carries a B-size (1") ball. RAM lists no aircraft types, so measure your yoke tube first.
Video: RAM Mounts
Twist-Lock suction cup: the iPad suction mount for the windscreen
RAM calls its Twist-Lock suction cup base “a must for use on airplane windshields” with “an extra strong hold on any smooth, nonporous surface”. The RAM-B-166-202U kit combines the 3.3" (≈ 84 mm) cup, a medium arm and a round plate whose hole pattern, RAM says, “will connect to most RAM cradles and 3rd party cradles”. Fit it low in a windscreen corner or on a side window, outside your forward view.
Tough-Claw rail clamp
The Tough-Claw small (RAP-B-400U) needs no tools; RAM names “aircraft yokes” among its popular locations. It clamps round rails of 0.625"–1.5" (≈ 16–38 mm) and flat surfaces up to 1.14" (≈ 29 mm).
Kneeboard
RAM also makes kneeboards and arm straps “for comfort and mobility”. They are not in our online catalogue; ask us.

Recommended RAM Mounts bases for the cockpit
Buying for a fleet or a tender? Ask us for a quote.
Get a quoteChoose the X-Grip holder for your iPad, iPad mini or phone
RAM's X-Grip uses a spring-loaded “X” that “expands and contracts” to fit the device. Measure it with its case, sleeve or skin on, as RAM advises; all three holders take a depth of up to 0.875" (≈ 22 mm).
| Device | RAM holder | Width range (RAM) | Connects to the arm |
|---|---|---|---|
| iPad and other 9"–11" tablets | X-Grip for 9"–11" tablets (RAM-HOL-UN9U) | 6.25"–8.1" (≈ 159–206 mm) | Round plate with B ball (RAM-B-202U) |
| iPad mini and other 7"–8" tablets | X-Grip for 7"–8" tablets with ball (RAM-HOL-UN8BU) | 2.5"–5.75" (≈ 64–146 mm) | B ball built in |
| Phone | X-Grip phone holder with ball (RAM-HOL-UN7BU) | 1.875"–3.25" (≈ 48–83 mm) | B ball built in |
RAM's lists include the iPad (10th and 11th Gen) for the 9"–11" holder, every iPad mini up to the iPad mini (A17 Pro) for the 7"–8" holder, and many Samsung and Lenovo tablets. The holders with a built-in ball include an optional tether. RAM also sells complete X-Grip suction cup kits for both sizes (RAM-B-166-UN9U, RAM-B-166-UN8U).
Video: RAM Mounts
Recommended RAM X-Grip holders for iPad and iPad mini
Buying for a fleet or a tender? Ask us for a quote.
Get a quoteKeep the arm short and the controls and view clear
Use the short B-size arm (RAM-B-201U-A), 2.42" (≈ 61 mm) overall, to keep the device close to its base. RAM rates a B ball at about 2 lb (≈ 0.9 kg): “Approximate capacity for a standard ball with a mid-length arm. Shorter arms and steel-reinforced posts increase real-world capacity.” More in our RAM ball sizes guide.
For non-commercial flights in other-than-complex motor-powered aircraft, EASA's AMC1 NCO.GEN.125 says a viewable stowage device “should not be positioned in such a way that it obstructs visual or physical access to aircraft controls and/or displays, flight crew ingress or egress, or external vision.” If the EFB moves or comes loose, the pilot-in-command should ensure “it will not jam flight controls, damage flight deck equipment, or injure any person on board.” Source: AMC/GM to Part-NCO, ED Decision 2019/008/R; check EASA's current Easy Access Rules.

Check on the ground, from your normal seat:
- Move the yoke through its full travel in every direction. For certified mounting devices, EASA's AMC 20-25A considers “full and free movement under all operating conditions”; use the same check for any mount, stick or helicopter control.
- Make sure no instrument, display, switch or exit is blocked.
- Check your forward and side view.
- Check that you can read the screen and reach its controls.
- Keep harness buckles clear and tighten the arm knob.
Secure the cables and check the mount before each flight
AMC1 NCO.GEN.125 says cables “should not hang loosely in a way that compromises task performance and safety”, and the crew should be able to “easily secure the cables out of the way during operations (e.g. by using cable tether straps)”. Leave enough length for full yoke travel. Any power connection to the aircraft follows its documentation and your authority's rules.
Before each flight, check that the knob is tight and the device sits firmly. RAM says suction-cup rubber “is considered a general wear item”: inspect it, and replace a worn cup with the Twist-Lock suction cup base (RAM-B-224-1U). RAM's pages give no temperature or altitude figures for the cup.
SCANSHOP is an official RAM Mounts reseller. Flight schools, clubs and operators fitting several aircraft can send us device models and yoke tube sizes for a quote. For ground vehicles, see our guides to airport ground support equipment tablet mounts and locking tablet mounts.
Frequently asked questions
What is the best iPad yoke mount?
For yoke tubes of 0.625"–1.25", one RAM setup is the Yoke Clamp Base with Ball (RAM-B-121BU), a short B-size arm and an X-Grip holder sized for your iPad.
Can a suction cup hold an iPad on an aircraft windscreen?
RAM calls its Twist-Lock suction cup base “a must for use on airplane windshields”. Mount it outside your forward view and check the cup before each flight.
Are RAM EFB mounts EASA or FAA approved?
RAM does not state any aircraft approval or certification for them. Follow the aircraft's documentation and your authority's rules for stowing a portable EFB.
Which RAM mount fits an iPad mini?
The X-Grip holder for 7"–8" tablets with ball (RAM-HOL-UN8BU). RAM lists every iPad mini up to the iPad mini (A17 Pro).
Does RAM make kneeboards for pilots?
Yes, RAM offers kneeboards and arm straps. They are not in our online catalogue; contact us.
Used in this guide
Compatible consumables and accessories for the RAM Mounts Yoke Clamp Base with Ball for 15.9–31.8 mm Rails, B-Size (RAM-B-121BU).
Products used in this guide
| Product | Price | ||
|---|---|---|---|
![]() |
RAM Mounts Yoke Clamp Base with Ball for 15.9–31.8 mm Rails, B-SizeRAM-B-121BU | 43,84 €+VATIn stock | |
![]() |
RAM Mounts Double Socket Arm, B-Size, Short Arm 44.5 mmRAM-B-201U-A | 23,46 €+VATIn stock | |
![]() |
RAM Mounts Twist-Lock Suction Cup Mount with Round AMPS Plate, B-Size, Medium ArmRAM-B-166-202U | 64,93 €+VATIn stock | |
![]() |
RAM Mounts Tough-Claw Small Clamp Base with Ball for 15.9–29 mm Rails, B-SizeRAP-B-400U | 53,32 €+VATIn stock | |
![]() |
RAM Mounts X-Grip Holder for 7–8" Tablets with Ball, B-SizeRAM-HOL-UN8BU | 70,62 €+VATOut of stock | View |
![]() |
RAM Mounts X-Grip Universal Holder for 9–11" TabletsRAM-HOL-UN9U | 141,71 €+VATOut of stock | View |
Related guides
Send us your model and a short description of the problem. Our team will help you find a solution.





